- Intake measurement of the club you own
- Trimmed baseline over at least 18 shots
- Single-variable component testing
- Printed spec sheet to take home
- Free re-check in eleven months
Studio › Rates
What it costs, printed where you can read it first
No quotes on request and no tiered names designed to make the middle option look sensible. These are the numbers on the wall of the shop.
100%Fee credited to a build
60Days to use the credit
$40Off each added session
$0Annual re-check
Fitting sessions
Three ways people usually buy the bench time
- Everything in a single-club session, twice over
- Gap ladder built across the whole scoring end of the bag
- Groove and edge-radius report on existing wedges
- Outdoor turf block when the weather cooperates
- Frequency reading logged for every head in the set
- Driver through putter in one afternoon
- Full gap ladder from the tee to 40 yards
- Lie board tape on every iron and wedge
- Written set specification, not just a recommendation
- Priority on the build queue afterwards
Junior sizing blocks are $70 for forty-five minutes, priced low deliberately because a growing player needs the appointment two or three times before they stop growing. Four-person weekday bay blocks are $420 for three hours.
Build and repair labour
Bench rates, separated from component cost
Components are billed at our landed cost plus a flat 22 percent, and we will show you the invoice line if you ask. The labour below is what pays for the bench.
| Bench work | Unit | Labour |
|---|---|---|
| Build from head and shaft, assembled and tested | Per club | $34 |
| Reshaft an existing head | Per club | $28 |
| Regrip | Per club | $6 |
| Loft and lie check | Full set | $45 |
| Loft and lie bend | Per head | $8 |
| Swingweight matching | Full set | $65 |
| Shaft frequency profile | Per club | $12 |
| Groove depth and edge radius report | Per wedge | $25 |
| Shaft tip trim and re-spec | Per club | $18 |
| Ferrule replacement | Per club | $14 |
| Broken shaft extraction | Per club | $22 |
| Putter length and lie adjustment | Per club | $30 |
The credit, in plain terms
How the fitting fee comes back
Place a build within sixty days of your session and the full fitting fee comes off the invoice. Not a percentage, not store credit, not a coupon with conditions. A $175 iron fitting followed by an iron build reduces the build total by $175.
If you book two sessions and then only build from one of them, the credit for the session you built from applies in full and the other stands. We do not stack unrelated fees onto a single purchase, because that would quietly turn the fitting fee into a discount scheme instead of what it is, which is payment for measured bench time.
Buying the components elsewhere is entirely fine and does not void anything. Bring them here and we will assemble them at the labour rates above. The spec sheet is yours regardless of where the hardware comes from — several clients take ours to an online retailer every year and we would rather they came back for the re-check than felt awkward about it.
Worked example — iron rebuild
Iron fitting session$175
7 heads, component cost$742
7 shafts, component cost$266
7 grips, component cost$77
Build labour, 7 × $34$238
Swingweight matching$65
Fitting fee credit−$175
Invoice total$1,388
Component figures are illustrative of a mid-range 2025 cast head and
a stock-weight steel shaft. Yours will differ; the labour lines will not.
Payment and cancellation
The administrative fine print, all of it
Deposit
$50 holds any session, taken when you confirm and applied to the total. Whole-bag Fridays take $150.
Cancellation
Full refund of the deposit with 48 hours' notice. Inside that window we will move you once without charge.
Builds
Half on order, balance on collection. Special-order heads are paid in full up front because we cannot restock them.
Cards
All major cards and cash. No surcharge on card. We do not offer financing and do not want to.